Manual Treadmill with Pulse
7HARDWARE PACKING LIST & TOOLSAllen Wrench 6M1 PCAllen Wrench with Phillips Screwdriver 5M1 PCWrench1 PC(63) Screw ST4x122 PCS(46) Bolt M8x55mm4 P
Step 1Attach both Left/Right Handlebar Support Tubes (10, 11) onto the Base Frame (7) with four M8x55mm Bolts (46), four M8 Nylon Nuts (57), and four
NOTE: PLEASE DO NOT FULLY TIGHTEN HARDWARE IN STEP 1 UNTIL STEP 5 IS COMPLETED.Hardware:9ASSEMBLY(46) Bolt M8x55mm4 PCS(57) Nylon Nut M84 PCS(59) Wash
Step 2Attach the Protective Cover (6) onto the Main Frame (5) with two ST4x12 Screws (63). Tighten screws with the 5M Allen Wrench with Phillips Scre
.10ASSEMBLYWrenchAllen Wrench 6MTool:Allen Wrench withPhillips Screwdriver 5M
Step 3Lift the front end of Main Frame (5) up by two or more people and thenattach the Main Frame (5) onto the Left/Right Handlebar Support Tubes(10,
Screwdriver and Wrench provided.Attach the Safety Tube A (24) onto the Main Frame (5) with oneM8x35mm Bolt (44), one Ø8.2xØ16x2T Nylon Washer (54), an
Step 4Connect the Hand Pulse Sensor Wire (12) and Extension Sensor Wire III(31) from the Right Handlebar (9) to the Extension Hand Pulse Sensor Wire (
Then install the Computer Bracket (14) to both Left/Right Handlebars (8, 9) by inserting the Computer Bracket (14) onto both Left/Right Handlebars (8,
Step 5Connect the Extension Sensor Wire I (33) from the Right Handlebar Support Tube (11) to the Extension Sensor Wire III (31) from the Right Handleb
SERVICE ------------------------------------------------------------------------ 2IMPORTANT LABELS ----------------------------------------------
NOTE: PLEASE FULLY TIGHTEN ALL HARDWARE INSTALLED INSTEP 1 TO STEP 5 WITH THE TOOLS PROVIDED.Hardware:(45) Bolt M8x45mm4 PCSASSEMBLYAllen Wrench withP
Step 6Remove two M5x10mm Bolts (52) from back of the Computer (15). Remove bolts with the 5M Allen Wrench with Phillips Screwdriver provided.Connect
Key functions:MODE: Display function selection. Press and hold theMODE key for 2 seconds, all data values will clear to zeroexcept the ODO (ODOMETER)
5. If the display is illegible or only partial legible, remove batteries and wait 15seconds before reinstalling.FOLDING UP THE TREADMILLTo fold up the
Adjusting the Incline AdjusterPlace one hand on the rear end of the Main Frame, thenlift the rear end of the Main Frame up and use the otherhand to re
belt will begin to stretch out.2.If the running belt begins to shift to eitherleft or right side, the user can standon the main frame and hold thehand
The treadmill has already been spread with "Silicone Oil" in advance before leaving the manufacturing plant. Silicone oil is without volati
PROBLEM: Treadmill running belt slips or is not centered on rear roller.SOLUTION: Refer to “Adjusting the Running Belt” section on page 18.PROBLEM: Co
WARM UP20Quadriceps StretchWith one hand against a wall for balance, reach behindyou and pull your right foot up. Bring your heel as closeto your but
Paradigm Health & Wellness, Inc. warrants to the original purchaser that this productis free from defects in material and workmanship when used fo
IMPORTANT: FOR NORTH AMERICA ONLYTo request product service and order replacement parts, please call our customer service department at: 1-866-924-168
4. Part Number5. Date of PurchasePARADIGMPARTS REQUEST FAX FORMPlease fax this form to (1-626-810-2166)OR YOU CAN EMAIL CUSTOMER SERVICE REQUESTS TOse
“YOUR ORDER WILL BE PROCESSED WITHIN 3 BUSINESS DAYS”PART # DESCRIPTION QTYOFFICIAL USE ONLYSHIP DATE: ___________________________________________TRK
2IMPORTANT LABELS
Basic precautions should always be followed, including the following safety instructions when using this manual treadmill: Read all instructions befor
consult an Authorized Service Representative.6.Wear comfortable and suitable clothing when using the treadmill. Do not use the treadmill barefoot, in
5PART LIST
No. Description Qty No. Description Qty001 Rear Roller Ø60x395 1 026 Safety Tube B (□25x460) 1002 Running Deck 1020x407x12 1 027 Spring Knob Ø8 1003 F
No. Description Qty No. Description Qty051 Handlebar Support Tube EndCap Ø282 058 Screw ST3x12 2052 Bolt M5x10mm 2 059 Washer M8 6053 C Clip Ø12 3 060
Kommentare zu diesen Handbüchern